TPKN2204三角铣刀片怎么配刀：刀盘压板、刀座与台阶加工
TPKN2204 Triangular Inserts: Match the Shoulder-Mill Body
旧刀盘换TPKN2204三角刀片，先核对完整刀体、压板和支承面，再确定钢件牌号、有效切深、精修余量与检测方案。
分类： Drawing-Based Tool Selection
APMT1135刀片怎么配小径铣刀：窄腔开粗与清角选型
APMT1135 Insert Selection for Small-Diameter Pocket Milling
以28毫米开口槽为例，说明APMT1135刀片与300R刀杆匹配、钢件槽型和牌号选择、排屑空间及精加工余量。
316L 卫生级阀体 CNC 案例：洁净孔精加工、螺纹铣削与密封面策略
316L Sanitary Valve Body CNC Case: Hygienic Bore Finish, Thread Milling and Seal-Face Strategy
316L 卫生级阀体通常有内孔、侧向螺纹口、法兰面和密封面。图纸强调内孔过渡和密封表面时，刀具方案要避免加工硬化、撕裂毛刺和后续工序划伤。
Ti-6Al-4V 骨板 CNC 案例：开槽、球头刀精加工与热量控制
Ti-6Al-4V Bone Plate CNC Case: Slotting, Ball-Nose Finishing and Heat Control
Ti-6Al-4V 钛合金板件常见窄槽、薄边、曲面过渡和边缘孔。图纸看的是轮廓和表面，工艺要额外关注热量。钛合金一旦刀口发钝或局部摩擦，尺寸和表面都会迅速恶化。
6061 铝合金薄壁电子机箱 CNC 案例：型腔粗加工、加强筋支承与毛刺控制
6061 Aluminum Thin-Wall Electronics Housing CNC Case: Pocket Roughing, Rib Support and Burr Control
6061 铝合金电子壳体看起来加工性很好，但图纸里一旦同时出现深腔、薄壁、加强筋、小圆角和外观倒角，刀具方案就不能只看效率。第一目标是控制薄壁振动和变形，其次才是提高去除率。
Tungsten Copper EDM Electrode Holder CNC Case: Precision Slots, Dowel Bores and Datum Control
A practical hypothetical…
Torlon PAI Compressor Valve Plate CNC Case: Thin Sealing Lands and Small-Hole Accuracy
A drawing-based hypothet…
Hastelloy C-276 Mixing Nozzle CNC Case: Compound-Angle Holes and Burr Control
A practical hypothetical…
Aluminum Bronze Bearing Sleeve CNC Case: Precision Bore, Oil Grooves and Cross Holes
A practical hypothetical…
AISI 1045 Taper-Lock Pulley Hub CNC Case: Taper Bore, Keyway and Radial Threads
A drawing-based hypothet…
15-5PH Pressure Sensor Flange CNC Case: Thin Diaphragm, Sealing Face and Port Tooling
A practical hypothetical…
304 Stainless Eccentric Clamp Hub CNC Case: Offset Bore, Radial Threads and Groove Tooling
304 stainless eccentric …